How to Install a Dog Door in a Stucco Wall

How to Install a Dog Door in a Stucco Wall

Published today• Posted by Hale Pet Door

Here is how to install a dog door in a stucco wall: first confirm the wall is hard-coat stucco, not EIFS (foam-backed "synthetic stucco"). Then cut the interior opening, drill reference holes outward with a masonry bit, and cut the stucco from outside with a diamond blade. Trim a self-framing tunnel to the wall depth, flash it, and caulk the top and sides.

The steps below follow Hale's Wall Model installation manual, with notes on what changes when the outside of the wall is stucco. For a brick house, see our brick wall install guide.

Can you put a dog door in a stucco wall?

Yes. The manual is written for stud walls, but it notes that the Hale Wall Model "can also be installed in any brick or block wall construction and with exterior brick, stucco, or siding." The spec sheet lists stucco as an application.

The Wall Model is self-framing: an aluminum tunnel joins the inside and outside frames. The manual says, "There is no need, nor is it advisable, to frame the inside of the wall cutout." For other wall types and models, see our wall dog door page.

Hard-coat stucco or EIFS? Check before you cut

What's behind traditional stucco

Building Science Corporation's BSI-029 describes hard-coat stucco as "typically a three layer cementitious rendering (scratch coat, brown coat and top coat)" applied "over a building paper, metal lath and sheathing."

So your exterior cut goes through hard cement coats, wire mesh (the lath), building paper and sheathing, then into the stud cavity. The building paper is the wall's water barrier, which is why a clean, square cut that the frame and caulk can seal matters.

How to tell if it's EIFS

EIFS (exterior insulation and finish system) looks like stucco but is foam insulation board, "usually expanded polystyrene," under a thin reinforced base coat and acrylic finish, per the ASHI Reporter article "EIFS: A Simple Approach to a Complex Issue". Its clues:

  • "Tapping on hardcoat stucco feels like tapping on thin concrete. It sounds solid." EIFS "has more give, and typically yields a hollow sound or very little sound."
  • EIFS usually stands out from the wall: "the thick (approximately 2-inch) wall system projection typical of synthetic stucco."
  • "There are hybrid systems that have acrylic finish over a hardcoat base."

The article's advice: "If you are not sure, do not guess!" House plans or a home inspector can settle it.

If your wall is EIFS

Don't cut it yourself. In a Walls & Ceilings homeowner Q&A, EIFS consultant Robert Thomas writes, "EIFS is not a DIY product," and says leaks are "almost always at the edge of the EIFS": at an opening, a penetration or a sealant joint. A pet door opening is that kind of edge, so have an EIFS contractor plan and seal it.

Measure the wall and choose the size

Measure from the face of the interior wall to the face of the stucco before you order; our wall depth checklist lists what to record. The Wall Model is "built for walls up to 10 inches thick" and "fully adjustable for any wall less than 10 inches," because you trim the tunnel during the install. Tunnels come in 10" and 16" lengths, and longer ones can be custom ordered. For walls over 10 inches, contact Hale.

For size, the manual says the top of the passage opening should sit above the shoulder of your largest pet, and "If in doubt larger is better." Use the pet door sizing guide to choose.

A Medium needs a 10 1/2" x 14 1/2" rough opening, a Large 13" x 18" and a Giant 17 5/8" x 29 5/8"; all sizes are in our dog door rough opening guide. The manual notes exterior wall studs "should be 16" on center, giving you 14" of room between studs." Extra Large, Extra Large Plus and Giant openings are 16" wide or more, so talk to an installer before you cut a stud.

Tools for cutting stucco

From the manual's tool list:

  • Stud finder, tape measure, pencil, 24" level, masking tape, drop cloths
  • Drill, a long drill bit and a 5/16" masonry bit
  • Drywall saw, reciprocating saw, and a circular saw with a diamond blade (the manual: "we recommend using a diamond blade to cut through stucco")
  • Tin snips, caulk and caulk gun, construction adhesive
  • Eye protection and gloves

OSHA's crystalline silica page says "sand, stone, concrete, and mortar contain crystalline silica," and that the dust causes silicosis, "an incurable lung disease." OSHA doesn't name stucco, but hard-coat stucco is cement plaster, so treat its dust the same way. For handheld power saws on these materials, OSHA's construction silica standard (written for work crews) lists a "saw equipped with integrated water delivery system that continuously feeds water to the blade." Wear a respirator and keep people and pets away until you've cleaned up.

How to install a dog door in a stucco wall, step by step

  1. Pick the spot. Leave room for the security cover to lift out (top-loading is standard; side-loading is available). Center between studs if you can, and look for signs of wiring or plumbing. The manual warns that hitting a power line or pipe "can result in severe injury or death."
  2. Mark the interior opening at the rough opening size, square and level, with drop cloths down on both sides.
  3. Cut a small test hole and check inside with a flashlight and your hand, then cut the full opening with a drywall saw and push the insulation aside.
  4. Drill reference holes through each corner, keeping the drill straight. The manual: "If you have exterior brick or stucco walls, be sure to use a masonry bit rather than the same bit you used on the interior wall."
  5. Mark the stucco by connecting the holes, square, level and in line with the inside opening.
  6. Cut the stucco. The manual allows a reciprocating saw started from drilled-out corners, and says "if you are cautious, a circular saw can be used on the outside wall." For stucco it recommends a diamond blade. Cut slowly; the outside frame needs a square opening to sit flat.
  7. Mark and trim the tunnel. Push the inside frame and tunnel through, hold the frame tight to the interior wall, pencil the tunnel along the stucco face, then cut on the line with tin snips.
  8. Caulk and set the flashing. Per the manual: two large beads on the bottom about 1/2" from the rear, a generous bead on the bottom and sides about 1" from the front, and a bead on the outside of both vertical flanges. Side flanges point up; the outside flange goes down against the wall.
  9. Attach the outside frame. Reinsert the tunnel, pull everything snug, hook on the raincap if you use it, and sleeve the outer frame into the tunnel. Drill through its pre-drilled holes with the 7/64" bit and drive the screws, plus two through the tunnel bottom about 2" to 2 1/2" back from the outer frame.
  10. Finish. Caulk the outside frame at the top and sides only, line the tunnel with the carpet using construction adhesive (not silicone, whose odor stays trapped between the flaps), and fit the security cover after peeling its film.

Keeping water out of a stucco wall

A new opening is one of the places water can get into a wall. ASHI notes that synthetic stucco problems develop where water gets through the skin, which "often occurs at joints and penetrations," and Building Science Corporation's BSI-103 treats "all punched openings" as joints and corners. The manual's details handle this:

  • Follow the flashing caulk pattern. The flashing is there so "any water is shunted to the outside of the wall."
  • Don't caulk the bottom. "DO NOT CAULK AT THE BOTTOM OF THE OUTSIDE FRAME. This will restrict the drainage of moisture should any accumulate inside the pet door."
  • Stay above the weep screed. Stucco over a stud wall ends at a metal or plastic weep screed near the bottom of the wall that lets trapped water drain out. Maricopa County's building policy on IRC Section R703.7.2.1 says it must sit at least 4 inches above the earth or 2 inches above paved areas, and "in no case shall the weep screed holes be covered by concrete, stucco or other material." Plan the opening so you don't cut through or cover the screed, even if your dog would like the door a little lower.
  • Use the raincap on exposed walls. It diverts water from above; the manual says you can skip it in protected spots such as under a covered porch.

Check the caulk line now and then. Walls & Ceilings notes that "caulking eventually wears out and must be replaced."

Matching the frame to your stucco

Wall Model frames come in brushed aluminum, dark bronze, white and Arizona beige, and the spec sheet says the colors "can be mixed to coordinate with interior and exterior colors of the home." Keep the pieces you cut out; the manual says they "can usually be used to patch the wall if the need to remove the pet door ever arises."

DIY or hire an installer?

The manual says "any person with a working knowledge of power tools and basic home construction can install the Hale Pet Door." If your wall might be EIFS, you don't have a diamond blade, or your opening crosses a stud, find an installer. The manual also says: "To reach an experienced installer for free consultation, please call 1-800-646-4773."

Frequently asked questions

Can you put a dog door in a stucco wall?

Yes. Hale's Wall Model installation manual says the Wall Model can be installed with exterior brick, stucco or siding, and the spec sheet lists stucco as an application. It is self-framing, so you trim its aluminum tunnel to the wall depth instead of framing the opening. Confirm first that the wall is hard-coat stucco and not EIFS.

What do you use to cut stucco for a dog door?

Drill reference holes through the corners from inside with a masonry bit, mark the outline on the stucco, then cut from outside. Hale's manual recommends a diamond blade on a circular saw, used with caution; a reciprocating saw started from drilled-out corners also works. Wear eye protection, gloves and a respirator, because cement dust contains crystalline silica.

How can I tell if my wall is stucco or EIFS?

Tap it. ASHI says hard-coat stucco feels like tapping thin concrete and sounds solid, while EIFS has more give and sounds hollow. EIFS also tends to stand out about 2 inches from the wall. Hybrid systems exist, so check house plans or ask a home inspector if you're unsure.

Should I caulk all the way around the outside frame?

No. Hale's manual says to caulk between the outside frame and the wall at the top and both sides, and not to caulk the bottom of the outside frame. Leaving the bottom open lets any moisture that gets inside the pet door drain out.

Do I need to frame the opening for a dog door in a stucco wall?

Not for the Hale Wall Model. Its manual says there is no need, nor is it advisable, to frame the inside of the wall cutout, because the aluminum tunnel is self-framing. Studs 16 inches on center leave about 14 inches between them, so wider sizes such as Extra Large and Giant may cross a stud; talk to an installer before cutting one.

Sources

  • Hale Pet Door, Wall Model Installation Instructions, product page and spec sheet
  • Building Science Corporation, BSI-029 and BSI-103
  • ASHI Reporter, EIFS: A Simple Approach to a Complex Issue
  • Walls & Ceilings, Finish Line: Homeowner Questions and Answers
  • OSHA, Crystalline Silica and 29 CFR 1926.1153
  • Maricopa County, Weep Screed policy DD-5004-01 (IRC R703.7.2.1)

Need help choosing the right pet door?

Get the right fit before you order

Compare Hale pet door models, use our sizing guide, or find a local dealer for expert help with measuring, product selection, and installation.

Other Posts